GNS3 Topology: BSCI – EIGRP & ISIS Redistribution Lab
Written by LBSources from http://www.gns3-labs.com on December 1st, 2008 | 5 CommentsOn November 15th I posted a lab contributed:BSCI OSPF Excercise Sim Question From Jim Shank. The lab was a great excercise where Jim pitched a scenario and requirement and the solution. Great lab! Jim sent me a new lab to share which is even better and has often proven to be a challenge for many. The labs is based on EIGRP & ISIS Redistribution of routes. Great practice for the CCNP seeker!
Orgrimmar Auction House has recently established a connection to the Thunderbluff Auction House to
share auction data. The two auction houses have been using separate routing protocols on their
networks, and a solution is required for the two Kalimdor clearing houses to begin sharing data
before the Alliance raid. A boundary router, Crossroads, has been setup to perform mutual
redistribution of route information between the two networks. For the Horde, you must configure
route redistribution from EIGRP into IS-IS and from IS-IS into EIGRP on the boundary router to
acheive the following requirements:
Seed metric for EIGRP must have the following
characteristics :
Bandwidth = 512 kbps
Delay = 100
Reliability = 255
Load = 1
MTU = 1500
Seed metric for IS-IS must be set to 50.
Only redistribute Level-1 IS-IS routes into EIGRP.
Redistribute EIGRP routes into IS-IS as
Level-1 routes.
May your blades never dull.
Solution in \Solution – BSCI REDISTRIBUTION SIM.txt
Routers Used: 3640
IOS: c3640-jk9s-mz.124-16a
Feature of Topology: EIGRP, ISIS, Route Redistribution
Image: 
Download: GNS3-Labs:: BSCI – ISIS & EIGRP Route Redistribution Lab
Enjoy .. LBS
25,502 viewsTags: 3640, BSCI, CCNP, EIGRP, GNS3 Lab and Exercise, GNS3 Topology, ISIS, Redistribution, Routing Protocols
You can leave a response, or trackback from your own site.
More from LBSources
- GNS3 Lab & Exercise: Inter-VLAN Routing using Catalyst Switch
- GNS3 Lab & Exercise: OSPF Case Study & Lab Scenario 3
- Petition Cisco for Educational IOS License!
- GNS3 Lab & Exercise: GNS3-Labs – BGP & EIGRP Case Study 4
- GNS3 Lab & Exercise: EIGRP & OSPF Route Manipulation
Subscribe to GNS3 Labs :: Cisco Router Simulator Network Topologies
January 3rd, 2009 at 4:29 pm
Dear Friend,
I am preparing for BSCI exams i have one doubt about delay in EIGRP, in Simulator if they give Delay=200 then i will divide by 10 and take Delay as 20 if 100 then 10.
Support in Exam Question if they give Eigrp parameter like this
Bandwith=64
Delay=3
Reliability=255
load=1
MTU=1500
when i redistribute EIGRP in ospf like this
“redistribute Eigrp 100 64 ? 255 1 1500
please tell me if they give 4 or 3 = delay then how much delay i have used in redistribution.
waiting for your reply.
bye
February 15th, 2009 at 12:21 pm
thank you so much
May 13th, 2009 at 4:25 pm
On a question I saw the only requirement was bandwith 512,so should the other units be 0? So redistribute isis metric 512 0 0 0 0? As no level on which isis routes to redistribute so leave that at default? Tried numerous times to input above whith diffent values and kept saying incomplete command.
August 20th, 2009 at 7:44 pm
This looks almost exactly like what’s on the BSCI exam. Might be troublesome with the NDA don’t ya think?
May 19th, 2011 at 6:24 pm
Articulately maintained and respected trap directory. Free admittance and moderation. Add your relation and you purposefulness be aware the power of our directory. do gazu!